HighlyCaffeinated's Photobucket Bridgeport BOSS album media

Old Steppers

HighlyCaffeinated — Wed, 25 Feb 2009 11:03:42 MST

HighlyCaffeinated posted a photo

Old Steppers - DSC02294Medium.jpg

DSC02295Medium.jpg

HighlyCaffeinated — Wed, 25 Feb 2009 11:03:41 MST

HighlyCaffeinated posted a photo

DSC02295Medium.jpg

DSC02296Medium.jpg

HighlyCaffeinated — Wed, 25 Feb 2009 11:03:40 MST

HighlyCaffeinated posted a photo

DSC02296Medium.jpg

DSC02297Medium.jpg

HighlyCaffeinated — Wed, 25 Feb 2009 11:03:39 MST

HighlyCaffeinated posted a photo

DSC02297Medium.jpg

No Longer Required!

HighlyCaffeinated — Wed, 25 Feb 2009 11:03:38 MST

HighlyCaffeinated posted a photo

No Longer Required! - DSC02298Medium.jpg

X Ways

HighlyCaffeinated — Wed, 25 Feb 2009 11:03:36 MST

HighlyCaffeinated posted a photo

X Ways - DSC02300Medium.jpg

Z ballscrew and limits

HighlyCaffeinated — Wed, 25 Feb 2009 11:03:34 MST

HighlyCaffeinated posted a photo

Z ballscrew and limits - DSC02302Medium.jpg

table after scotchbrite

HighlyCaffeinated — Wed, 25 Feb 2009 11:03:33 MST

HighlyCaffeinated posted a photo

table after scotchbrite - DSC02303Medium.jpg

Big guy in the front >little guy in back

HighlyCaffeinated — Wed, 25 Feb 2009 11:03:31 MST

HighlyCaffeinated posted a photo

Big guy in the front >little guy in back - DSC02305Medium.jpg

CNC control Panel

HighlyCaffeinated — Fri, 20 Feb 2009 08:42:09 MST

HighlyCaffeinated posted a photo

CNC control Panel - moto_0009.jpg

Buttons and knobs and displays, oh my!

Rode smooth and stable

HighlyCaffeinated — Fri, 20 Feb 2009 08:42:08 MST

HighlyCaffeinated posted a photo

Rode smooth and stable - moto_0010.jpg

Didn't move an inch all the way home.

The ride home

HighlyCaffeinated — Fri, 20 Feb 2009 08:42:07 MST

HighlyCaffeinated posted a photo

The ride home - moto_0012.jpg

Sam's Club 3" ratchet straps run in U-shapes, one front, rear, left and right over the table strapped it down plus one font and rear over the foot so it didn't go anywhere

In the air

HighlyCaffeinated — Fri, 20 Feb 2009 08:42:06 MST

HighlyCaffeinated posted a photo

In the air - moto_0013.jpg

Ready to set her down after pulling the trailer out from under.

Supah Man!

HighlyCaffeinated — Fri, 20 Feb 2009 08:42:05 MST

HighlyCaffeinated posted a photo

Supah Man! - moto_0014.jpg

Friend, truck owner and trailer borrower Brian "gettin' 'er done". Go Brian!

Rigging

HighlyCaffeinated — Fri, 20 Feb 2009 08:42:05 MST

HighlyCaffeinated posted a photo

Rigging - moto_0015.jpg

5-ton trolley and chain hoist locked into position using a 3" ratchet strap. The I-beam is on a pitch so the weight draws the machine down and left in this photo.

Terra Firma

HighlyCaffeinated — Fri, 20 Feb 2009 08:42:04 MST

HighlyCaffeinated posted a photo

Terra Firma - moto_0016.jpg

Touchdown! Lifted off the trailer and set on the shop floor. Came off much easier than going on with a 5-ton trolley and chain hoist.

Boss tape reader

HighlyCaffeinated — Fri, 20 Feb 2009 08:42:03 MST

HighlyCaffeinated posted a photo

Boss tape reader - moto_0017.jpg

This is where the CNC operator would load a punch tape reel for the machine to read. This punch tape held the program from which a part was made.